Skip to main content

Introduction to ArcGIS Reality Pro

Available with the Standard or Advanced license.

Available with the Reality Mapping user extension.

ArcGIS Reality Pro is an ArcGIS Pro extension that expands ortho mapping capabilities with high-fidelity 2D, 3D, and True Ortho product generation. ArcGIS Reality Pro is enabled using a Reality Mapping user extension license assigned by your ArcGIS Online or ArcGIS Enterprise organization administrator. ArcGIS Reality Pro requires a Professional or Professional Plus user type. See Start ArcGIS Pro with a Named User license for additional information. When ArcGIS Reality Pro is enabled, you can generate the following products from drone and digital aerial imagery:

  • DSM—A digital surface model (DSM) of the earth and features above the surface. This is generated from a collection of overlapping images.

  • DTM—Digital Terrain Model (DTM) of the earth with above ground objects such as trees, buildings, vehicles, and so on, removed. A DTM is also referred to as bare earth elevation.

  • True Ortho—An orthorectified image without perspective distortion so that above-ground features do not lean and obscure other features.

  • DSM Mesh—A 2.5D textured model in which the adjusted images are draped on a triangulated irregular network (TIN) version of the DSM extracted from overlapping images.

  • Point Cloud—3D points representing the ground surface and features above the ground, derived from overlapping imagery.

  • 3D Mesh—A 3D textured model in which the ground and above-ground feature facades are densely and accurately reconstructed.

  • Gaussian Splats—3D points rendered with a Gaussian distribution in a dense 3D point cloud, used to reconstruct high-fidelity 3D scenes that capture fine details such as thin structures.

Using satellite imagery, you can generate DSM, DSM Mesh, DTM, and True Ortho products. You can also collect, block adjust, and generate various 2D ortho mapping products from drone, digital aerial, scanned aerial photography, and satellite imagery.

Extension requirements

Photogrammetric processing using ArcGIS Reality Pro requires above average computer resources to improve performance and expedite processing. Data, project, system requirements and recommendations are listed in the sections below.

Data and project requirements

Data and project requirements are as follows:

Data type

Requirement

Sensor data

Drone, digital aerial, and satellite imagery

Image perspective

Nadir or oblique, or a combination of both

Minimum image overlap

60 percent forward, 30 percent lateral

Recommended image overlap

80 percent forward, 80 percent lateral

Recommended minimum number of images

100 nadir images, 300 oblique images

Image preprocessing

Block adjusted source imagery

System requirements

In addition to ArcGIS Pro system requirements, the following system requirements are recommended for optimal ArcGIS Reality Pro performance:

Item

ArcGIS Pro supported and recommended requirements

ArcGIS Reality Pro recommended extended requirements

CPU

Minimum: 2 cores, simultaneous multithreading

Simultaneous multithreading, or hyperthreading, of CPUs typically features two threads per core. A multithreaded 2-core CPU will have four threads available for processing, while a multithreaded 6-core CPU will have 12 threads available for processing.

A maximum of 48 CPU threads is supported.

  • Recommended—4 cores

  • Optimal—10 cores

A processor supporting AVX2 instruction set is required.

  • Recommended—4 cores or more

  • Optimal—10 cores or more

  • A processor supporting AVX2 instruction set is required.

GPU

Recommended

  • Minimum—None

  • Recommended—Current high performance graphics card supporting CUDA 13.2 with a minimum 8GB VRAM and a compute capability of 7.5 or higher. Check your computer’s compute capability at Nvidia.

Platform

x64 bit

x64 bit

Storage

  • Minimum—32 GB of free space

  • Recommended—More than 64 GB of free space

  • Recommended—Solid-state drive (SSD).

  • Minimum—1 TB of free space

  • Recommended—4 TB for projects with fewer than 1,000 images

  • Single-node processing—16 TB SSD RAID5

Memory/RAM

  • Minimum—8 GB

  • Recommended—32 GB

  • Optimal—64 GB or higher

  • Minimum—32 GB

  • Recommended—64 GB or higher

  • Optimal—128 GB or higher

Note:

Minimum 64GB RAM is required to generate Gaussian Splats.

Your computer's RAM requirement needs to be guided by the number of vCPU cores or logical processors supported. For example, a computer with 12 logical processors, ideally should have a minimum of 24 GB of RAM (2GB x 12 = 24GB) to support image processing. A higher RAM per logical processor ratio is recommended to support Reality Mapping processing.

Dedicated (not shared) graphics memory

Minimum—4 GB or more

If using a notebook computer with an integrated GPU, consider increasing the system RAM to compensate for the use of shared memory.

Recommended—8 GB or more

If using a notebook computer with an integrated GPU, consider increasing the system RAM to compensate for the use of shared memory.

Visualization cache

The temporary visualization cache for ArcGIS Pro can consume up to 32 GB of space, if available, in the user-selected location. By default, the visualization cache is written to the user profile’s \Local subfolder so it does not roam with the user profile if roaming profiles are enabled by your system administrator.

The temporary visualization cache for ArcGIS Pro can consume up to 32 GB of space, if available, in the user-selected location. By default, the visualization cache is written to the user profile’s \Local subfolder so it does not roam with the user profile if roaming profiles are enabled by your system administrator.

DirectX

Minimum: DirectX 11, feature level 11.0, Shader Model 5.0

Minimum: DirectX 11, feature level 11.0, Shader Model 5.0

OpenGL

  • Minimum—OpenGL 4.3 with the ARB_clip_control and EXT_texture_compression_s3tc extensions

  • Recommended—OpenGL 4.5 with the ARB_shader_draw_parameters, EXT_swap_control, EXT_texture_compression_s3tc, and EXT_texture_filter_anisotropic extensions

  • Minimum—OpenGL 4.3 with the ARB_clip_control and EXT_texture_compression_s3tc extensions

  • Recommended—OpenGL 4.5 with the ARB_shader_draw_parameters, EXT_swap_control, EXT_texture_compression_s3tc, and EXT_texture_filter_anisotropic extensions

Screen resolution

  • Minimum—1024x768

  • Recommended—1080p or higher

  • Minimum—1024x768

  • Recommended—1080p or higher

Gaussian splats requirements

If you select Gaussian splats as the output product, your processing machines must meet the following requirements:

Item

Supported and recommended

GPU

  • Minimum hardware: NVIDIA GPU with CUDA compute capability 7.5 or later

  • Minimum software: CUDA 13 or later

GPU VRAM

  • Minimum: 8GB

  • Recommended: 16GB or more

Additional software requirement

Installation of deep learning libraries

Frequently asked questions

See the Frequently asked questions (FAQ) topic for more details about ArcGIS Reality Pro.

See the Install ArcGIS Reality Pro topic for details about installing and licensing ArcGIS Reality Pro.